![]() ![]() The Lutron call centers are US-based and exceptionally helpful. If you are looking for product support, don't be afraid to call Lutron's tech support at 1.844.588.7661. Replacing a standard light switch with a dimmer takes about 15 minutes, and its actually one of the easiest ways to start saving energy around your home. ![]() If applicable, relevant pictures from your installation.In other words, don't post a picture of wires and say "Help!" with no context. A concise description of what you are trying to achieve or solve (2-3 sentences).If available, the exact model of the product you're describing and a link to the product page from an online retailer.Examples: Quantum, RadioRA 3, standalone (like SUNNATA or Maestro), etc. The Lutron ecosystem for your product.If you are posting with a question or issue, please include the following information: Section 1: MS-OPS2/MS-VPS2 Installation The MS-OPS2 and MS-VPS2 Sensor Switch can only be installed in a single-pole application. No Reddit tropes (this is the way, switcheroo, joke chains, etc.).A Lutron three way dimmer that is similar to what you have would have one red, one red/white striped, one solid black, and a green. Meaning it is designed to operate in one location. No advertising/selling/self-promotion without prior approval 1 Answer Sorted by: 2 Edit: From your picture and descriptions you appear to have a three way switch.Lutron-related discussions only (no politics, memes, off-topic, etc.).In addition to the standard Reddit rules, please abide by the following: Many thanks in advance.Post here to discuss Lutron products, planning, installation, and support. ![]() Each dimmer switch controls a pair of recessed ceiling lights. There are three of them in a 4-gang box (the 4th switch seen in the pics is on a different circuit that controls a stairway light and was already replaced). Any and all help would be much appreciated. 2 I'm trying to replace some older (late-1980s) Leviton incandescent-only dimmers with new Lutron LED-compatible ones. I'm pretty much a noob with all of this and have tried to describe it as accurately as possible using what I hope is proper lingo from what I've garnered through research trying to understand all of this. Do those have to be connected too, or can they be ignored (or gathered together and capped?) since, I assume, the circuit is presently already grounded. The old switches don't have ground wires, but the new switches do include a green ground. To find a diagram for a specific product or system, please use the drop-down menus below. Also, the bare grounds from the Romex are all pigtailed and screwed into the box. Search the Lutron archive of wiring diagrams. Connect both tagged wires (note wire color) removed from 4-way switch to blue screw terminal on companion switch (one wire to screw terminal the other to push-in terminal). I'm puzzled about how to wire Sw2 since it's a 3-way. Wire the companion switch replacing a 4-way switch Connect green wire on companion switch to bare copper or green wire in wallbox. However instead of three wires plus ground on the original switch, there are 4 wires plus ground. Like the others, the switch I am replacing is a 3 way. For Sw-1/3 I'm thinking I can cap the unneeded red/white on the Lutrons and use either the black or red interchangeably to replace the older two-black config on the Levitons. I have installed several of the Lutron Diva dimmer switches in my house with no problem. All whites from Romex are gathered to one wire nut. I'm guessing that the hot is coming from the black in Romex-2, which goes back to the lights (load) via black into Romex-1/3/4 (or, in the case of Switch 2, possibly via the Romex red in Romex-3?). I've drawn a diagram to show the present wiring config. I'm using new Lutron Skylark C-L 3-ways (with 1 black wire, 1 red, 1 red/white, 1 green) for all three (I can just cap the unneeded red/white wire provided for traveler on the new Lutrons per instructions in the packaging). The older Leviton single-poles have only two black wires while the 3-way has two black and one red wire (all hardwired-no screw mounts). The center is a 3-way that controls another pair of lights that are also controlled by a toggle switch on an opposite wall (also already replaced). The two switches on the outside (left and right-see pics) are single-pole and each control one pair of lights. I'm trying to replace some older (late-1980s?) Leviton incandescent-only dimmers with new Lutron LED-compatible ones. How do you install a Lutron CL dimmer switch Varies depending on whether you are installing a single switch or are switching the light from 2 locations. Need help or have a question Our new Support Center can easily help you out. ![]()
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |